BRAND NEW COMES WITH 5 years warranty (after registration)
Features
| 8 channel, Digital, high power audio amplifier. Power Factor Correction, 2Ω operation, 2RU. 500/ch @ 4Ω, 250W/ch @ 8Ω, 500W 70/100V line DSP & Dante |
|
|
|
|
|
|
|
Features
Power supply
- Universal switch mode power supply up to 400VAC tolerant with Power Factor Correction
- Patented output filter with ripple cancellation network
- Low Inrush Limiting reduces AC inrush current, removing the need for expensive power sequencers
- Detachable AC mains cable with IEC C19/22.2 (16A for EU, 20 A for USA) socket
Protections
Fully protected circuit design with:
- Ac protection: shut down power supply when AC mains voltage is outside operating range
- Clip limiter: prevents severely clipped waveforms from reaching loudspeakers, while still maintaining full peak power output
- DC protection: protects against infrasonic signal at the outputs
- VHF protections: protects the loudspeakers against non audible, strong, non musical high frequency signals
- Short circuit protection: protects the amplifier from short circuit or other stressful events for the output circuits with automatic protection reset
- Long term limiter: protects the loudspeaker against steady long term RMS (non audio) signals, by reducing maximum output
- Thermal protection: output stages operating temperature up to 80 °C (176 °F)
- Temperature controlled continuous variable speed fan, front to back airflow
General
- Fixed frequency switch mode output stage for high grade sound accuracy
- All models 2 RU for reduced rack cost and space
- Light weight - for easier racking and shipping: 14 kg / 30.8 lbs
- Standard Phoenix connectors: analog and digital input, audio outputs, aux supply, alarms and GPIO
- Remotely switchable double input
Loudspeaker system configuration
- Direct drive either low impedance loads or 70V / 100V Hi-Z distributed lines
- Switchable 35Hz / 70Hz high pass filter per channel
- Mixed configuration with Lo-Z/Hi-Z systems possible
- Bridged mode, with low impedance, per channel pair
Digital Signal Processing
- TI C6000 DSP platform architecture
- AD/DA converter: dual 24bit @ 96 kHz Tandem® architecture, 127 dB dynamic range, per channel
- Input/output independent equalizers per channel providing Raised-cosine, custom FIR, parametric IIR: peaking, hi/lo-shelving, all-pass, band-pass, band-stop, hi/lo-pass
- Crossovers: linear phase (FIR), hybrid (FIR-IIR), Butterworth, Linkwitz-Riley, Bessel: 6 dB/oct to 48 dB/oct (IIR)
- Input delay up to 2s and output delay up to 100ms for time alignment per channel
- Active DampingControl™ for cable compensation
- Power limiter (TruePower™, RMS voltage, RMS current) + Peak Limiter
Alarms and GPIO
- NC/NO contacts per channel for alarm notifications
- Remote ON/OFF switch
- Remote AUX/MAIN inputs switch
- PWS OUT connector providing 24VDC
Remote management
- Control and monitoring through ArmoníaPlus
| GENERAL |
| Output power per channel |
| Output power per channel |
450 W @ 2 Ω |
500 W @ 4 Ω |
250 W @ 8 Ω |
| Bridge mode |
900 W @ 4 Ω |
1000 W @ 8 Ω |
|
| Max output voltage / current |
| Max unclipped voltage @8 Ω |
|
|
65 Vpeak |
| Current |
|
|
15 Apeak |
| AC MAIN POWER |
| Power supply |
Universal, regulated switch mode with PFC (Power Factor Correction) |
| Nominal power requirement |
|
|
100-240 V ±10%, 50-60 Hz |
| Operating voltage |
|
|
90 V – 264 V |
| Power consumption/current draw |
| Idle |
|
115 V: 74 W – 0.85 A |
230 V: 77 W – 0.75 A |
| 1/8 of max output power @ 4 Ω |
|
115 V: 740 W – 6.6 A |
230 V: 750 W – 3.9 A |
| THERMAL |
| Operating temperature range |
|
|
0° – 35° C – 32° – 95° F |
| Thermal dissipation* |
| Idle |
|
115 V: 253 BTU/h – 64 kcal/h |
230 V: 263 BTU/h – 66 kcal/h |
| 1/8 of max output power @ 4 Ω |
|
115 V: 801 BTU/h – 202 kcal/h |
230 V: 839 BTU/h – 211 kcal/h |
| 1/4 of max output power @ 4 Ω |
|
115 V: 1340 BTU/h – 338 kcal/h |
230 V: 1340 BTU/h – 338 kcal/h |
Dimensions 483 x 89 x 360 mm 19.0 x 3.5 x 14.2 in
Weight 14 Kg (30.8 lb)
Loading... Please wait...
